Just how do you really feel in regards to A Step-by-Step Guide to Installing a Bathtub?
Mounting a bathtub isn't precisely brain surgery, yet it does require solid plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably difficult project. If the old tub is easily easily accessible, the task can relocate speedily; if you have to open a wall to eliminate the old bathtub and also place the brand-new bathtub, the task is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also embeded in the new one. Make sure you have qualified yourself for the job and are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed job, it is much better to take into consideration using one prior to you start. Opportunities are you might require an expert plumber to make tube links.
This post will certainly assist you set up a new tub in your restroom if you have already bought a brand-new bathtub and also do not require to alter the plan of your previous supply of water pipes.
Your tools and product list must make up the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your installation, then the first thing you need to do is separate the water system. After doing so, turn on the taps to drain pipes any kind of water staying in the system. The process of removing the existing faucets can be rather troublesome due to the limited accessibility that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a towel prepared for the staying water that will originate from the pipes. Once the supply pipelines have been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from turning throughout this process. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Before moving on to fit the brand-new taps, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end offers a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washers remain in place in between the tap and also the sink. Protect the faucet in place with the maker provided backnut. As soon as the tap is safely in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular tap ports. The previous type must be connected to the tap finishes first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Bath tub
Using the two wooden boards under its feet, put the bath tub in the required setting. The wood boards are useful in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four little factors.
The next goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the tub up until the level reads level.
To set up faucets, fit all-time low of the furthest flexible tap port to the ideal supply pipe by making a compression join; then do the exact same for the various other faucet.
Switch on the supply of water as well as examine all joints and also brand-new pipework for leaks and tighten them if required. Fill up the bath tub as well as additionally check the overflow outlet and the typical electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the manufacturer's instruction manual. Tiling and sealing around the tub must wait up until the tub has actually been made use of at the very least when as this will certainly resolve it right into its last placement.
Preparing for the Installation
To start with, the sustaining structure provided with the bath ought to be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is essential to ensure that if the tap comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid stress on the tub.
Fit the flexible tap connectors to the bottom of both faucets making use of 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you make use of every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be fitted in its final placement.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to split a rigid seal, creating the water to permeate the wall in between the bath and the tiling, bring about problems with dampness and also possible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and can sealing voids up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bath tub with water before securing, to enable the activity experienced when the tub remains in use. The sealer can break rather early if you do not think about this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily readily available on the market. It is a good idea to fit the tiles utilizing waterproof or waterproof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a person who reads about Tools You Need to Install a New Bathtub , I was thinking sharing that portion was worth the trouble. I beg you take the time to share this blog posting if you appreciated it. Thanks for your time. Don't hesitate to check up our blog back soon.
Maintenance Sign-Up